SW900 LCD DISPLAY CONTROLLER — INSTRUCTIONS WOULD HELP

I make no claim of being an expert on e-motors. That being said I have had seven different e-motors on my trike thus far. The first three were all BionX which the dealer installed. Even with them I had the experience of uninstalling them and reinstalling them myself. And all of the rest of the motors I installed myself. What I am trying to say is that by now I have had quite a lot of experience installing and uninstalling e-motors. The clutch went out on my last e-motor so I started looking at what is available to replace it. I don’t care for crank drive motors so didn’t bother looking at any of them.

I found a complete motor conversion kit for only $469. That does not include a battery but I already have a few batteries so $469 was an attractive deal. Of course, it comes from China and there are no helpful instructions that are provided. Installing it was not a problem but getting it to work without instructions was quite challenging. Fortunately I was able to find instructions online which was a big help. I got it running but the top speed was quite slow. I was ready to send it back for a refund when I sort of accidentally stumbled across the problem and got it resolved. If only the Chinese would include instructions all of this could have been avoided.  For what it is worth, I just now found one user manual which covers what the problem was and why I wasn’t getting much speed or power out of this new motor. Anyway, I am writing this article in hopes it will help others in getting their self installed e-motor system up and running.

My new system uses the LCD-SW900 display console controller which is a common display console controller various e-motor manufacturers use. I did not use the cadence assist hardware component in my installation. I may install it sometime in the future. I only have a manual thumb throttle hooked up. Upon completing the installation using a 48 volt battery (this motor is made for 72 volts) my top speed was only 5.6 mph and had no torque available at all to climb the slightest incline. I rode it that way for a couple of days.That is a mighty slow ride but still better than I can do on my own without any e-motor assist. About 2/3 of the way into my second day of riding so slowly I just happened to discover the answer to more speed and power. I pushed the UP ARROW button on the 3 button control which caused it to go from power level one to power level two. (PAS — power assist — level is displayed at bottom left corner of SW900 display) Simple enough but without any knowledge and understanding of how it works … well … I was stuck at 5.6 mph as when first turning the system on PAS 1 is what it starts out in by default. If only they had provided instructions. Anyway, I knew that 5 levels of e-motor assist were programmed into the SW900 display console controller so I continued to press the UP ARROW button watching it change up to assist level 5 and experiencing more speed and power with each level of increase. Hallelujah! ! Happy days are here again! Definitely this is the most powerful e-motor I have had installed yet. It is not as fast top speed as my former e-motor but I am really liking it as it is whisper quiet and far more powerful. I am tempted to buy a 72 volt battery just to see if this motor will perform as advertised … about 45 mph top speed. I am nearly 76 years old and probably should avoid the temptation as I would likely find myself careening off of a tree unless I wrapped myself around it. BTW, to go down in the assist level pushing the DOWN ARROW button lowers it one level at a time. Turning power on and off is accomplished by holding the middle button down a few seconds. So if you find yourself in the same situation I was in hopefully this will help you.

Speaking of help:

SW900 manual

SW900 manual

SW900 manual with the error codes for troubleshooting

SW900 manual with the error codes for troubleshooting

KEEP ON TRIKIN’

A FREE GIFT AWAITS YOU!

You are invited to come join the Tadpole Rider Facebook Group. Please note that in order to join you must first answer the two membership vetting questions and agree to comply with the group rules.

Author: Steve Newbauer

I have a few current blogs (tadpolerider1, navysight, truthtoponder and stevesmixedbag) so I am keeping busy. I hope you the reader will find these blogs interesting and enjoy your time here. Feel free to email me at tadpolerider2 at gmail dot com (@gmail.com)

One thought on “SW900 LCD DISPLAY CONTROLLER — INSTRUCTIONS WOULD HELP”

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

This site uses Akismet to reduce spam. Learn how your comment data is processed.